Explorer Motorhomes paint protection, Gold Coast

Explorer Motorhomes Ceramic Coating on the Gold Coast

Certified Fireball ceramic coating, matched to the surface and applied in our Ashmore workshop by a team with 25+ years on paint.

Rated 5.0 on GoogleCertified Fireball InstallerPrice in WritingAfterpay Available

By submitting you consent to being contacted about your enquiry.

What Explorer Motorhomes owners should know

A one-piece fibreglass body moulded by a boat builder. Keep yours looking like the day you drove it home.

Explorer Motorhomes builds compact 4WD motorhomes in Australia on the Toyota HiLux and Ford Ranger, from the Vision and Discovery to the Nomad, Pathfinder, Spirit and Xtreme. They're made to go places bigger motorhomes can't, and they spend the rest of their lives parked outside in Queensland sun. Book a time, bring yours in to our Ashmore workshop, and we'll take it from there.

We protect every kind of Explorer Motorhomes:

A ute cab and a fibreglass body

An Explorer is a Toyota HiLux or Ford Ranger with a one-piece fibreglass body on the back. The cab is automotive paint and the body is fibreglass, so they don't respond to the same products or the same pressure. Treat them as one surface and you end up with a cab and body that never quite match.

Built for dirt roads

Explorers are 4WD motorhomes, and owners use them that way. Red dust and mud work into every edge and seal, and scrubbing them out of a matt, unprotected surface takes the gloss with it. On a coated body, dirt rinses off with far less effort and far less rubbing.

The peak over the cab takes the hits

The rounded peak over the cab is the first thing the wind, bugs and sun meet on every trip. It's where bug residue bakes on and gloss goes first. On a coated peak, bugs come off with a soft wash instead of a scrubbing brush.

The roof nobody looks at

The roof takes more sun than any other surface and is the one nobody climbs up to check. It's also where the hatches, solar panels and their sealant live. We look it over before anything is coated, because a beautiful finish over a tired seal helps no one.

What Explorer Motorhomes paint is really like

An Explorer body is a single fibreglass moulding with a foam core: no wall-to-roof joins, no seams. It's built by a team whose founder spent 30 years building fibreglass ski boats and cruisers, and the finish shows it. That smooth fibreglass suits a ceramic coating perfectly, and it can be machine polished. On a new or near-new Explorer there's usually very little correction to do, so the time goes into preparation and getting the coating on before Queensland UV starts working on it. The HiLux or Ranger cab in front is ordinary automotive paint and is prepared separately. Left unprotected, fibreglass oxidises, going dull, then chalky.

Models we protect

Including, but not limited to:

NomadVisionDiscoveryPathfinderSpiritXtreme

Our answer: we prep your Explorer Motorhomes for what its paint actually needs, then lock it in with Fireball.

How the job runs

How We Prep Your Explorer Motorhomes Before It’s Coated

Preparation is the job. The coating is the last hour of it.

  1. 01Full inspection under LED and swirl-finder lighting, with paint depth readings recorded panel by panel.
  2. 02Two-bucket hand wash, wheels and arches degreased, badges and shuts cleaned out.
  3. 03Chemical iron and industrial fallout removal, then a clay treatment to lift bonded contamination.
  4. 04Tape-up of trim, rubbers and sensitive edges before any machine work.
  5. 05Careful preparation of the fibreglass. On a new or near-new Explorer that usually means thorough decontamination and a light polish rather than heavy cutting. Where an older body has started to dull, we test a section first to see how much gloss comes back before deciding on the approach.
  6. 06Cab prepared as automotive paint, body as fibreglass, with decals, seals, hatches and badges worked around by hand.
  7. 07Panel wipe with a coating-safe solvent to strip polishing oils and reveal the true finish.
  8. 08Fireball ceramic coating applied by hand, levelled panel by panel under controlled lighting.
  9. 09IR / controlled cure, then a final inspection and handover pack with aftercare instructions.
Working along a motorhome roofline from the ladder
Motorhome mid-correction with compound across the side wall
Cleaning an RV roof before sealing

Fireball Professional Systems

Why Explorer Motorhomes Owners Choose Gold Coast Polishing

The Fireball ceramic coating range

How It Works

1

Enquire

Send the details and a few photos, and get your price in writing.

2

Lock in a date

We’ll confirm the day that suits you.

3

Bring it to Ashmore

We do the work under cover in our workshop and hand over your aftercare guide.

2/1 United Road, Ashmore, Gold Coast

Customers come from Byron Bay to Brisbane.

What Our Customers Say

Rated 5.0 on Google

Questions Explorer Motorhomes Owners Ask

Can’t see yours? Call or text and you’ll get a straight answer.

What does it cost to coat an Explorer Motorhomes?

Every Explorer Motorhomes is different in size, surface and condition, so we price it from the details and photos you send. You get the price in writing before anything is booked.

What warranty do I get?

Fireball Silla+ with a 5-year warranty or Butterfly+ with up to 7 years, matched to your van at inspection.

Can you come to me?

No. All work is done at our Ashmore workshop, under cover with proper lighting, water and power. That’s a big part of why the finish lasts.

How long will it be with you?

It depends on the size and condition. You’ll get a timeframe with your quote.

Do you take Afterpay?

Yes.

Where are you?

2/1 United Road, Ashmore, on the Gold Coast.

Enquiry

Get Your Explorer Motorhomes Price Today

Tell us the make, model and size, and send a few photos if you can. We’ll come back with a price in writing.

Reach us through

By submitting you consent to being contacted about your enquiry.